DIY MODERN CANDLE CHRISTMAS TREE

Loading...

Learn how to build a DIY Modern Candle Christmas Tree out of wood using just a few supplies from a home improvement store such as Lowe’s. This easy tutorial for beginners takes you step-by-step through the building process.

DIY MODERN CANDLE CHRISTMAS TREE (4)(1)

I knew that this year I wanted to add a Christmas tree to the room but was having difficulty finding coral-colored ornaments. After giving it some thought, I decided it would be fun to create a modern, wooden candle holder tree and googled the idea to see if it had been done before. Sure enough it had been done before!

DIY MODERN CANDLE CHRISTMAS TREE (5)(1)

TOOLS NEEDED:

  • Saw
  • Drill and bits (3/4 spade, 13/16 spade, 3/4 bit)
  • Kreg jig
  • Tape measure
  • Mask/respirator, ear plugs, safety glasses
  • Clamps
  • Sander or sanding block.

MATERIALS NEEDED:

  • (4) 2x2x8 Furring Strip
  • (4) 1 1/2″ pocket screws
  • (1) 3/4″ x36″ dowel rod
  • (37) 5″ DRIPLESS taper candles (I could only find 10″ tapers so cut them in half using a hot knife.)
  • Spray paint (optional)

CUT LIST:

I made the cuts up as I went along and now I really wish that I had written down the order of the cuts for you! I used up all four furring strips with very little waste. If you’re good at math, you’ll be able to figure out how to make the following measurements work. The nice thing about this project is that the measurements do NOT have to be perfect. I wanted most of my boards to be different lengths to ensure the candles had room to breathe. I recommend cutting your dowel rod last after assembling and measuring exactly where to cut to ensure a perfect fit.

  • (2) 18″
  • (2) 8.4″
  • (2) 24
  • (1) 26″
  • (1) 29″
  • (1) 28″
  • (1) 27″
  • (1) 25.5″
  • (1) 23″
  • (1) 21″
  • (1) 17.5″
  • (1) 16″
  • (1) 15″
  • (1) 14″
  • (1) 13″
  • (1) 10.5
  • (1) 8
  • (1) 6

STEP 1: CREATE YOUR BASE.

Take one of your 18″ strips and the two 8.4″ strips and create an “X” using your Kreg jig and 1 1/2″ pocket screws. Using your 3/4″ spade bit, drill a hole most of the way through your wood being careful not to drill all the way through. Place your dowel rod in the center hole. You can use wood glue to secure your dowel rod in place. I chose not to glue the dowel so that I can easily disassemble the tree at the end of the season. If you are going to light your candles frequently, I highly recommend gluing the rod in place for safety reasons.

DIY MODERN CANDLE CHRISTMAS TREE (1)(1)

STEP 2: DRILL AND SAND YOUR STRIPS.

Using your 3/4″ bit, drill a hole all the way through the center of each strip. Using your 13/16″ spade bit, drill most of the way down on each end of each strip. These will act as your candle holes. Sand any rough spots.

STEP 3: PRIME AND PAINT. (OPTIONAL)

I used one can of Zinsser primer and 2 cans of Krylon Coral Isle spray paint for this project. The spray paint adds about $15 to the total cost of your project so keep that in mind. You’ll want to allow your spray paint to dry overnight or longer to ensure it is cured.

DIY MODERN CANDLE CHRISTMAS TREE (6)(1)

STEP 4: ASSEMBLE YOUR TREE.

Place your strips in the following order starting with the base and dowel.

Strip 1: 24″ Strip 10: 18″
Strip 2: 26″ Strip 11: 17.5″
Strip 3: 29″ Strip 12: 16″
Strip 4: 28″ Strip 13: 15″
Strip 5: 27″ Strip 14: 14″
Strip 6: 25.5″ Strip 15: 13″
Strip 7: 24″ Strip 16: 10.5
Strip 8: 23″ Strip 17: 8″
Strip 9: 21″ Strip 18: 6″

Place all of your candles in the candle holes. Use mounting puddy or tinfoil to secure any loose candles. Enjoy!

DIY MODERN CANDLE CHRISTMAS TREE (2)(1)

Loading...